1 |
Hybrid INSTALL Document |
2 |
|
3 |
$Id$ |
4 |
|
5 |
Copyright (c) 1997-2013 IRCD-Hybrid Development Team |
6 |
|
7 |
---------------------------------------------------------------------- |
8 |
|
9 |
+------------------------------------------------------------------------+ |
10 |
| Note for those who don't bother reading docs: | |
11 |
| | |
12 |
| Reading INSTALL is now a must, as the old DPATH is now specified when | |
13 |
| configure is run. | |
14 |
| | |
15 |
| - You now need to ./configure --prefix="/path/to/install/it" as a | |
16 |
| minimum. Try ./configure --help or read this file for more info on | |
17 |
| the possible options you can pass to configure. | |
18 |
+------------------------------------------------------------------------+ |
19 |
|
20 |
---------------------------------------------------------------------- |
21 |
|
22 |
HOW TO BUILD |
23 |
|
24 |
As of hybrid-4, the distribution uses GNU autoconf instead of the old |
25 |
Config script. You must run ./configure before you can (sanely) build |
26 |
ircd-hybrid. |
27 |
|
28 |
1. Read the NEWS file to find out about the exciting new features in |
29 |
this version. Other good reads are doc/reference.conf, and README. |
30 |
|
31 |
2. Run the configure script. It will create config.h and the |
32 |
Makefiles to match your system. The paths are now handled |
33 |
with the --prefix option to configure. |
34 |
/usr/local/ircd is the default if no prefix is specified. |
35 |
|
36 |
./configure --prefix=/usr/local/ircd |
37 |
|
38 |
The script will determine whichever of the following is best for |
39 |
your system, but you may (unsupported) force their usage with |
40 |
undefined results: |
41 |
|
42 |
* --enable-kqueue - Use the superior kqueue(2) system call as |
43 |
opposed to the default poll(2). This is currently only available |
44 |
on FreeBSD 4.1 or higher. |
45 |
|
46 |
* --enable-devpoll - Enable the superior /dev/poll support on |
47 |
Solaris. Linux /dev/poll is broken and will not work with this |
48 |
option. |
49 |
|
50 |
* --enable-epoll - Enables epoll(4) Signal I/O system. This is |
51 |
currently only available on 2.5.44 Linux kernel versions or |
52 |
later. |
53 |
|
54 |
* --enable-poll - Use POSIX poll(2). |
55 |
|
56 |
* --enable-select - Use POSIX select(2). |
57 |
|
58 |
Incidentally, the order of listing above is the order of auto- |
59 |
detection in configure. So if you do have kqueue but wish to |
60 |
enable select(2) instead (bad idea), you must use --enable-select. |
61 |
|
62 |
* --enable-openssl - Enable the openssl dependent crypto functions. |
63 |
Required for the SSL Challenge controlled OPER feature, compressed |
64 |
and/or SSL/TLS server links, as well as SSL/TLS client connections. |
65 |
|
66 |
On systems where the configure script can automatically detect |
67 |
OpenSSL, this option is not necessary. If configure cannot find |
68 |
OpenSSL, you must specify a path with this option |
69 |
(--enable-openssl=/path/to/openssl) |
70 |
|
71 |
|
72 |
These are optional or have default values that may be overridden: |
73 |
|
74 |
* --enable-assert - Enable use of numerous debugging checks. This |
75 |
should not be used on any production servers for maximum speed |
76 |
so as to prevent cores from things that shouldn't normally happen. |
77 |
|
78 |
* --enable-debugging - Prepares Makefiles to compile the ircd sources |
79 |
with proper settings that are required for debugging purposes. |
80 |
This switch basically sets CFLAGS to "-g -O0". |
81 |
|
82 |
* --enable-halfops - Enable halfops (%, mode +h) usage. Halfops |
83 |
are similar to plain ops, but can't kick/deop plain ops. Halfops |
84 |
may or may not kick/deop other halfops depending on if (+p) is |
85 |
set. Halfops may not set (+/-p). |
86 |
|
87 |
|
88 |
3. Run 'make'; this should build the ircd. |
89 |
|
90 |
4. Run 'make install'; this will install the server, modules, and tools |
91 |
in the path with the prefix specified when configure was ran. |
92 |
|
93 |
---------------------------------------------------------------------- |
94 |
|
95 |
HOW TO GET HELP |
96 |
|
97 |
- Send Check or Money Order to... just kidding! You're on your own for |
98 |
support. Try asking other ircd-hybrid admins on EFnet if you can't |
99 |
fix it yourself. If you do fix anything, however, please send context |
100 |
or unified diffs to bugs@ircd-hybrid.org so the fixes can be |
101 |
incorporated into the next release of ircd-hybrid. If hybrid crashes |
102 |
on you, PLEASE contact bugs@ircd-hybrid.org ASAP with a backtrace of |
103 |
the core. The Hybrid team can't fix bugs if no one tells us about them! |
104 |
|
105 |
- https://lists.ircd-hybrid.org/mailman/listinfo/hybrid |
106 |
Here you can subscribe to a mailing list for general discussion of Hybrid. |
107 |
|
108 |
---------------------------------------------------------------------- |
109 |
|
110 |
NOTES |
111 |
|
112 |
The best way to get a backtrace of the core is to follow this sequence of |
113 |
instructions: |
114 |
|
115 |
1. Change to the directory containing the core file |
116 |
|
117 |
2. Run gdb on the binary and the core file. With an unmodified ircd-hybrid |
118 |
installation, an example command line is below (in the /usr/local/ircd |
119 |
directory) |
120 |
|
121 |
$ gdb bin/ircd ircd.core |
122 |
|
123 |
|
124 |
3. At the "(gdb)" prompt, enter the command "bt full" |
125 |
|
126 |
4. Save the output of the backtrace command and send it to |
127 |
bugs@ircd-hybrid.org. |
128 |
|
129 |
5. Be sure to save the ircd binary, the modules, and the core file in a |
130 |
safe place in case the developers need to look deeper than a backtrace |
131 |
provides. |